35 Measure Motorcycle Chain Slack

The first step is to measure the initial chain slack. The total travel is 15 inches from where it hangs.

Chain Slack Correct Measurement Honda Motorcycles Fireblades Org

According to the manual for my 99 standard range is 35-40 mm and 35-45 mm usable range.

35 measure motorcycle chain slack. If the first reading is 255mm and this reading is 295mm thats 40mm slack ensuring youve measured to the same point on the chain. Never clean or lubricate your chain while the engine is running. Make sure the chain is adjusted not too loose but also not too tight.

Consult your owners manual for the recommended amount of chain slack. Measure the distance between the point when the chain is pushed up and the chain is pushed down. The difference is your chain slack.

I found about the middle portion of the chain and lifted it up to see how far it travels. Push the tube down over the measuring scale to set the scale to zero. Clean the chain at regular intervals to extend chain life.

Pull up on the chain while holding the rule steady and read the difference. Put the bike on its centerstand. Your second measurement with upwards pressure on the chain.

I need to measure 35 MM chain slack at mid-point below swingarm. It could be possible it wasnt adjusted correctly as I wouldnt expect it to stretch that much over those few miles. Step 2 With the.

When I lift it up though it hits a chain guard. To get an accurate reading hold a tape measure in front of the chain and look across the top of the links. It doesnt matter if you measure from the top of the chain bottom of the chain or someplace inbetween as long as you use the same spot both times.

For this bike it should be 35-40mm. Find the point on the chain halfway between front and back sprocket on the bottom run of the chain. OK this is probably a dumb question but Im a little unclear on how to measure the chain slack.

Check that your cleaner is safe to use on O-ring chains. Press the chain up towards the swingarm and measure how far the same point is from the swingarm now. A common chain slack measurement is 25-35 mm for example.

Most streetbikes also have a sticker on the swingarm. Step 1 Read the owners manual for the correct amount of drive-chain slack. To measure chain slack take a measurement of the play in the chain above or beneath the swingarm using a chain slack tool or tape measure.

The manual is vague on the details of exactly how the slack is measured. Youll want to make the measurements midway between the sprockets. Says the chain slack to be within 1020 mm without a load a rider on the bike.

In fact they call for the bike to be on either the side or centre stand. Grab the cardruler in one hand and the chain in the other. In the old school method you hold a millimeter rule and place one of the easy to remember and easy to subtract from index points at the bottom or top or center of the slack chain.

A 520-118 chain has a pitch of 520 and it has 118 chain links. If the slack is adjusted to 35 mm with no load when I sit on the bike the slack is about 20mm that. Motorcycle Chain Slack - YouTube.

A rivet is from swingarm. Find the middle of the chain place a ruler against the swingarm at that point tug the chain down a little and measure how far a specific part ie. Press down on the chain slightly to make sure it is at its lowest point.

The only place there is any room to position the tool properly between the swingarm and the chain and measure is close to the rear sprocket but obviously that would be an inaccurate measurement. On the Ninja thats between 35 and 45mm. The difference between your two measurements is your chain slack.

If youre trying to find out the right chain size for your motorcycle then you can refer to your owners manual. When your chain is cold measure the slack halfway between the sprockets by moving the chain up and down. Place the fork on the Slacksetters sliding arm over the chain and hold the top of the tool against the underside of the swingarm.

The shape of the swingarm and the muffler make it impossible to position anywhere near the center point. The chain slack setting for your motorcycle is found in the owners manual and it should tell you where to take the measurement. As a reference the Versys 650 Ninja 650 have it specd between 25-35mm Measure the slack at the middle of the chain run.

Rotate the rear wheel until the chain is at its tightest and measure the chain slack before making any adjustments. If its a used bike then you may have to check the size-stamping on your current chain. Keep in mind that if you measure a value between 20-30mm the chain slack is correct and you dont have to do.

Remember the correct chain slack for this bike is 20-30mm when measured roughly at the middle of its length. The official Triumph shop manual calls for a maximum slack vertical movement of 35 to 40 mm for the Tigers chain. I always adjusted it to 1 254mm slack as the stock spec seems way too tight.

Chains are generally categorized by pitch and length. In this case we measured 35mm which is out of spec and way too loose. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features.

Measuring Chain Slack Below the Swingarm. Should the chain be adjusted to the spec with no load on the bike I hear the light noise from the chain or the sprocket area when I push the bike forward.

Bicycle Bike Cycling Tool Spoke Tension Meter Measurement Tool Gauge Wire Wheel Buy On Zoodmall Bicycle Bike Cycling Tool Spoke Tension Meter Measurement Tool Gauge Wire Wheel Best Prices Reviews Description